Traction-Talk  

Go Back   Traction-Talk > Advertisements > Wanted Adverts
Register Donate Events Calendar Picture Albums Mark Forums Read

Wanted Adverts Steam items and equipment Wanted.

Reply
 
Thread Tools Display Modes
  #1  Post / In Thread 
Old 18th July 2016, 12:36 PM
Ashley smith Ashley smith is offline
Engineer
 
Full Name: Ashley smith
Join Date: Sep 2015
Posts: 184
Default Small milling machine wanted

Me and my grandad are after a small milling machine preferably one that we can squeeze into the cellar, we are currently getting by with a vertical slide on the ML7 but are finding it hard work, we have no experience in milling machines so suggestions welcome, thanks
Ash
Reply With Quote
  #2  Post / In Thread 
Old 18th July 2016, 12:57 PM
Paul30013's Avatar
Paul30013 Paul30013 is offline
Engineer
 
Full Name: Paul Kemp
Join Date: Dec 2011
Location: Kent
Posts: 1,840
Default

Ashley,

Go for the largest and most rigid machine you can fit in. I am really stuffed for space and I bought a micro mill (vertical sq column which tilts). When I did my 4" RP I managed to mill the cylinder block flange on it but it was really well outside the machines proper capacity and I had to take baby cuts, but it did get the job done. I have just done most of the operations on the body casting of the water pump for my 6" LS (going to post some pictures in the next week or so if I get time) but again it needed careful planning and light cuts.

Thus, I would go for a vertical machine, try for 3 T slots in the table with a decent table travel X and Y. Look at the spindle travel, distance of spindle from the column and maximum distance from spindle nose to table. What looks generous can very quickly be eaten up by collet chuck and then putting a vice or worse a rotary table on the table. I have been looking at Warco milling machines for my next one, they seem to be reasonably heavily built with a reasonable spec for the £'s.

Paul.
__________________
Strange - There is never enough time to do the job properly but there is always enough time to do it again when it goes wrong!
Reply With Quote
  #3  Post / In Thread 
Old 26th July 2016, 07:08 AM
Ashley smith Ashley smith is offline
Engineer
 
Full Name: Ashley smith
Join Date: Sep 2015
Posts: 184
Default

Anything?


Sent from my iPhone using Tapatalk
Reply With Quote
  #4  Post / In Thread 
Old 26th July 2016, 08:21 AM
Gaudin98 Gaudin98 is offline
Engineer
 
Full Name: Dale Riley
Join Date: Aug 2009
Location: Lancashire
Posts: 1,080
Default

Tom Senior M1 is a good small machine.
Reply With Quote
  #5  Post / In Thread 
Old 8th August 2016, 10:58 AM
Ashley smith Ashley smith is offline
Engineer
 
Full Name: Ashley smith
Join Date: Sep 2015
Posts: 184
Default

Still looking to purchase one if anyone is thinking of upgrading/ selling one? Thanks again


Sent from my iPhone using Tapatalk
Reply With Quote
  #6  Post / In Thread 
Old 8th August 2016, 12:13 PM
SimonT SimonT is offline
Engineer
 
Full Name: Simon Thomas
Join Date: Aug 2010
Location: Round the bend, but not yet over the hill.
Posts: 477
Default

Quote:
Originally Posted by Gaudin98 View Post
Tom Senior M1 is a good small machine.
Wholeheartedly agree. Avoid most of the modern rubbish which is intended to look big but often can barely support itself, let alone do anything useful.

Buy a Senior M1, with both horizontal & vertical attachments and decent machine vice (Abwood, or similar). The only shortcoming will be that your z-axis (up & down) is via the knee, not a quill. They take MT tooling, so you can share some bits with the Myford. They are near indestructable, will machine things far larger than they were originally designed to do and swapping from 3-phase to single is a simple motor swap. They split easily (base, tray, column, knee, rear cover & motor), which makes taking them through the house possible if needed. The horizontal arbour support bar is invaluble for lifting the column back up once all the bits are in the correct room...

Look in the back of Model Engineer or Engineering In Miniature and you should find something fairly soon. Fairly that, try your local model engineering club. They are often asked to find homes for workshop equipment from deceased members etc.

Simon.
Reply With Quote
  #7  Post / In Thread 
Old 8th August 2016, 01:29 PM
Socket Head Socket Head is offline
Oily Rag
 
Full Name: Mervyn Greeves
Join Date: Mar 2010
Posts: 4
Default milling machine

I have a tom senior major milling machine nin good condition fixed head, s type head slotting head plus tooling as I said all in very good condition £ 2, 900.ono
Reply With Quote
  #8  Post / In Thread 
Old 9th August 2016, 02:36 PM
Ashley smith Ashley smith is offline
Engineer
 
Full Name: Ashley smith
Join Date: Sep 2015
Posts: 184
Default

A little too much machine for me sadly my budget won't stretch but thanks for the offer


Sent from my iPhone using Tapatalk
Reply With Quote
  #9  Post / In Thread 
Old 11th August 2016, 01:36 AM
Steamcar's Avatar
Steamcar Steamcar is offline
Engineer
 
Full Name: Stephan Gaal
Join Date: May 2011
Location: Melbourne Aust
Posts: 4,470
Default

If you are tight on space and short on cash have a look for a Rodney Milling attachment for the Myford.

http://www.homemodelenginemachinist....ad.php?t=22043

Small and fiddly sure but a step up from the vertical slide.
Alas they are hard to come by.

However if the concept of how it works will do the job for you you might be able to find some other type of small milling head to bolt to the tail stock end of the bed and use in a similar way.

http://www.lathes.co.uk/staines/

Something from a very small mill drill for example.

I know Maximat made a 4 speed milling head with a 2 morse that bolted to the back of their lath bed in the middle that worked in the same way.

All depends on what you can find.

Might even be able to modify a small drill press to do the job.
Reply With Quote
  #10  Post / In Thread 
Old 11th August 2016, 01:50 AM
Steamcar's Avatar
Steamcar Steamcar is offline
Engineer
 
Full Name: Stephan Gaal
Join Date: May 2011
Location: Melbourne Aust
Posts: 4,470
Default

Here is the Maximat.
http://www.ebay.com/itm/Emco-Maximat...-/371553083188
You just need the milling head.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 02:37 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.